2016年5月30日星期一

How to change the rechargeable battery on the IQ4CAR Mega Macs 50 tool?

How to change the rechargeable battery on the IQ4CAR Mega Macs 50 tool?

Procedure:

1.Switch off mega macs 50 and remove all connecting leads.
2.Remove the protective casing, starting at the narrow end.


3.Remove six fastening screws using a suitable tool, e.g. >PH1<.

CAUTION
Do not pull off any cable plugs
4.Open up the back panel to the right.


5.Carefully lever off the plastic cover using a suitable tool.



6.Replace the batteries, pay attention to correct polarity.
7.Reassemble in the reverse order.



NOTE
Recycle used batteries in accordance with the applicable environmental and disposal regulations

2016年5月29日星期日

Opcom OP-Com Can OBD2 Opel Firmware V1.45 Software Updated to V2012!

Opcom OP-Com Can OBD2 Opel Firmware V1.45 Software Updated to V2012!

V2012 Installation Tips:

1) Whether your computer system is windows XP or windows 7, you need to install the “dotnetfx35_SP1″ system path to run the V2012 software.
2) If your computer system is windows 7, you need to open the software by administrator way. You can see this from the install video in the software CD before installing.

V2012 Opcom OP-Com Can Opel Software Display:









2016年5月27日星期五

Connect HiCOM To The Vehicle – Starting With Diagnosis

Connect HiCOM To The Vehicle – Starting With Diagnosis

HiCOM is diagnostic tool for Hyundai and Kia vehicles. It supports all OBD2 compliant vehicles since 1996.

1. Connect the HiCOM interface to your computer. LED indicator should start blinking.

2. Connect HiCOM to OBD-II connector in the vehicle.
If you cannot find location of the OBD-II connector, you can use HiCOM location image database,available under OBD-II Connector location from main menu:




3. Set-up HiCOM application

4. Select Settings from HiCOM main menu and configure HiCOM interface port. If no ports are shown, click Refresh button. Then choose appropriate port and click on Test Interface to make sure everything is OK. Then you should see updated interface information. Now click on Apply changes or Save changes button to save changes and return to main menu.

2016年5月26日星期四

How To Add Free Tokens for SKP-900 Auto Key Programmer?

How To Add Free Tokens for SKP-900 Auto Key Programmer?

SuperOBD SKP-900 Key Programmer is Hand-held OBD2 key programmer. SKP-900 Key Programmer can support almost all cars in the world, such as Ford, Land Rover, Chrysler, Jeep, Toyota, Nissan, Honda, Mitsubishi, Hyundai, Kia, and so on...

You need to go to the official website: http://www.superobd.com/ to register and login,then click the "download" menu, download and install the program named
"SKP-900_Add_Free_Tokens (2014-01-11)".


1. Connect SKP-900 with computer using USB cable.

2. Start SKP-900 and select ADD FREE TOKENS

3. Run the activation software, scan the ports or manual select a port(port number less than COM 9)

4. Click "Activate" and waiting for success


2016年5月25日星期三

How To Unlock Radio Code And Use Vin Relearn By GM Tech2?

How To Unlock Radio Code And Use Vin Relearn By GM Tech2?

Here Is The Step-by-stap Instruction on clear radio theftlock for GM(GM,SAAB,OPEL,SUZUKI and HOLDEN)models with GM TECH2 diagnostic tool
Tools needed:
GM TECH2 diagnostic scan tool
Candi interface


Tech2 Theft-lock Procedure:

Well set up CANDI module with tech2 main unit,connect tech2 scanner with vehicle
1.Select<diagnostics>at the main menu screen
2.At the <vehicle identification>screen,select the following options:
-model year>>>(radio came from an 04 escalade or whatever)
-LD Trk,MPV,incomplete;
3.Select <body>at the <system selection>menu screen
4.At the <vehicle identification>screen,select the following:
-Appropriate model
-appropriate air conditioning
-Navigation radio
5.Select <navigation radio>at the <body>screen
6.Select <special functions>at the <radio>screen
7.Select <vin relearn>at the <special functions>screen
8.At the <vin relearn>screen,the tech2 will display <do you want to clear radio theft information?>
9.To begin clearing,press the soft touch key on the top right of the scan tool,the scan tool will display <clearing radio theft in progress>
10.Press <exit>on the scan tool and cycle the ignition.

How To Install ADS1500 Oil Reset Tool

How To Install ADS1500 Oil Reset Tool

ADS1500 Oil Reset Tool is an auto maintenance resetter. It is made by ADS TECH INC. It reset latest cars with CAN BUS and VPW and KWP2000 agreements. It supports most of Europe, America, Asia and Chinese brands vehicles (some models do not support the device to reset, only support manual reset, we have installed the materials of manual reset for most models).






Steps 1: Copy file“APK”into mobile phone memory card and find a program
named “My Files”.

Steps 2: Open the My Files >>> All Files>>> sdcard0>>>ADS1500 oil
reset tool , and find out “ADS1500 oil reset tool.apk”.

Steps 3: click and it will display the interface, click the
“Install” button and start to install .

Steps 4: After complete installation, it will display "Application installed".

Steps 5: Then the “ADS1500 Oil reset tool” software icon will display on the
application program interface.


2016年5月22日星期日

V4.94 Digiprog3 Odometer Master Successfully Tested and Failed Car Model

Digiprog III 4.94 Successfully Tested and Failed Car Model

I bought the V4.94 Digiprog 3 from https://eforshop.en.alibaba.com 1 month ago. After testing some cars, I shared my testing result with you.

("Ok" means the car model successfully changed mileage by V4.94 Digiprog III Digiprog3 Odometer Master.)

Worked Car Model:

1)For VW, Audi, Skoda vehicles:

Passat 2007 —> OBD OK
passat 2011 work obd 5 min
passat 2012 work obd
passat cc 2012 work obd
Passat 2011 menu dash diag -2012 read ok/write ok /3 minute.
passat 2006 dash work
passat 2011 work by OBD

Tiguan 2007 —> OBD OK
tiguan 2009: ok test Many Time always ok
Tiguan 2011 OBD no problem, takes about 10 minutes

Jetta 2013 take golf 6 on car list. Work fine 2 minutes
jetta 2012 work obd
jetta 2014: ok test Many Time always ok

Skoda Superb (3t) II 2009y only by obd less then 5min
Skoda Roomster 2009 —> Diag work Perfect
Skoda octavia 2009 1.9tdi instrument ok, ecu ok, dsg reset ok
SKODA Fabia 2009 obd ok. fabia -diag-read -write ok. (digi4.94)
skoda superb 2011 nec+24c64 obd works fine.

audi a4 2010 obd ok, audi a3 2010 obd ok
A6, 2009 work OBD, 4-5 minute.
no problem with audi a3 for now 2011 and 2010 doing ok by obd

Volkswagen Eos obd2 ——ok
vw eos 2007 —> Diag obd2 work

Golf 6 2012 obd ok
golf 2007: dash and dsg ok
golf mk5..ok
Golf 4 MM Just open dash en look voor 24C** it takes 2 minutes

300 m 2009 ok
wrangler 2012 ok
VW evoque 2012 work by OBD
Seat MII 2013 —> OBD Work

2)For BMW vehicles:
BMW E46 2004 —> 35080 Clip Work

3)For Ford vehicles:
Ford Fiesta 2012 —> OBD OK
Ford Fiesta HCS12 —> ST48 Work
2012 Ford Focus – 95320 – by ST1 work ok

4)For Mitsubishi:
For read & write correct Mileage use
Mitsubishi Outlander 93C86 V2 —> Work Perfect on Peugeot 4007 2012

5)For Mercedes Benz:
w211 2005 dash via st60 read ok/write ok/ezs sync blocked ok.
E39 m5 dash done with digi using st47
MERCEDES w210 E – DB 4_99 with Stecker 10 , ok!

6)For Opel:
-Opel Vivaro 2013 —> EEPROM Clip work 93c76
-Astra J 2011 work by OBD.
-Opel Insignia 2014 —> OBD Work perfect

7)For Fiat:
Fiat Grande Punto EVO 2011 dash– obd OK…. fiat doblo
Fiat Ducato 2012 work perfect OBD
Fiat Doblo 2009 —> OBD Work perfect 1 sec. Job

8)Other models:

Galaxy 2008 new model by the OBD ok
Successfully made chevrolet orlando like a opel insignia

Digiprog read/write 35080 for 100%.

Range Rover Evoque 2013 via obd ok

Nissans: 2002 Altima 93C66 OK in circuit with Murano; 2001 Xterra 93c56 OK unsolder with Patrol

Toyota RAV 4 2007 —> eeprom clip 93c56 work

Made : sportage 2012
Swift 2014
Ranger 2010
Prado 2006
Runner 2006
Navarra 2012

All eeprom on board …i did NOT try obd
salvage Yard
nitro 2009 ok
patriot 2013 ok
2015 xtrail does work with digiprog 4.94, chip 93c86 worked a treat
volvo s80 2008+ work good 10min.

Failed Car Model:

Digiprog V4.94 cannot work on some
Digiprog 3 can not do some Golf 6 and Polo Dash by obd.
Digiprog 3 can do only VDO dash Golf 6 by obd, not Magneti Marelli.
A3 sportback 2009. killed
Focus 2011 not work

2016年5月20日星期五

How To Install V-checker Iobd Module B342 ?

How To Install V-checker iobd module B342 ?

V-Checker iobd module B342 are suitable for all OBD standard cars which manufactured after 2001, with the connection between Bluetooth and module B342. Users can acquire vehicle condition (Speed, Coolant temperature, Engine speed, Fuel consumption, etc) & various of real-time warning (DTC, Over-Speed, high coolant temperature, fatigue driving) with installing APP on mobile phone.


Step1: unpack the V-checker iobd module


Step2: Find the OBD connection in your car, It usually located under the steering wheel, above the brake pedal if you cannot find it ,Please contact your local 4S dealer.


Step3: Turn on your ignition key, start your car, keep your car under idle mode.


Step4: Plug iobd module into OBD socket correctly the  indicate will keep flashing, System will scan vehicle protocol automatically for 2 minute.


Step5: Run V-checker APP, initialize the iobd module settings refer to the steps on the screen.



2016年5月19日星期四

FREE SHIPPING PLUS 5% DISCOUNT For Motorpartstore

FREE SHIPPING PLUS 5% DISCOUNT For Motorpartstore


Welcome to Website(www.motorpartstore.com/freeshipping)! This website have the specialize experience on motor parts.Our products are good in quality and cheap in price.There are many models in our store. Such as Honda, Kawasaki, Suzuki, Polaris and TaoTao.Especially recently we are doing FREE SHIPPING PLUS 5% DISCOUNT activity.If there are interested in this aspect of the motorcycle parts. Welcome you into the web site to see.

For example

How To Use TM100 Key Programmer When You Lost All Original Key ?

How To Use TM100 Key Programmer When You Lost All Original Key ?

With this TM100 programmer, you can cover, read, write and generate the latest transponders used in the latest vehicle immobilizer technologies.



1) Remove IMMO box from instrument cluster
2) user XPROG M to read out the 93C66 data and save it to your PC.
3) Open TM100 software, find 93C66 module of Toyota Camry after 2005
4) Clike "open file" to upload 93C66 data you saved before.
5) choose "use original facotry chip", click "OK", Choose "Key position 1" to write start. Then TM100 will generate the new data.
6) Write this data back to 93C66.
7) Install the IMMO BOX back to your car. Use the new key to start your car directly.

Usage for the Tacho Pro 2008 Universal Correct Audi Model A3 / S3 VDO before model 2000

Usage for the Tacho Pro 2008 Universal Correct Audi Model A3 / S3 VDO before model 2000

Tacho pro 2008 Description:

Tacho Universal is the most sold programming-device for digital speedometers worldwide. The system is a high-quality tool, which offers a maximum of flexibility and working comfort despite simplest operation.
You can serve almost any vehicle with the Tacho Universal.

The OBD II -plug needed:

Opreation Instruction: 

 Turn ignition on.
• Connect the Tacho Universal to the OBD II plug and the diagnostic port.
• Select the menu AUDI-A3-VDO-Diagnosis.
• The Tacho Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK

2016年5月18日星期三

NitroOBD2 VS EcoOBD2

NitroOBD2 VS EcoOBD2

Some users are confused NitroOBD2 or EcoOBD2. In order to help sort them out, make a comparison table from the following aspects. Wish it can help you.

Usage for the ScanMaster-ELM327

Usage for the ScanMaster-ELM

Super mini ELM327 Highlights

1.Software Version: V2.1
2.Hardware version: V1.5
3.It is compatible with 1996 and later vehicles. Connecting to your iPhone / iPod touch /iPad is made by WIFI connection in adHoc mode.
4.WI-FI OBD AUTO CHECKER is capable of communicating with vehicles which adopt following protocols:
ISO 9141
ISO 11898(aka. CAN)
ISO 14230(aka. KWP2000)
ISO 15765(aka. CAN)
SAE J1939




Double-click the ScanMaster-ELM DEMO icon to start it.
You may need to config it as shown below:


Click the button, choose WLAN in the drop list which resides in the tab named Communication
Enter 192.168.0.10 as the IP address and 35000 as the port number. Click OK. Now the software is ready to
use.
These are what you’ll see when the software is running:





Note: This piece of software is a demo version. It only provides some basic features. If you want all the features, you can
buy it from http://www.wgsoft.de

2016年5月16日星期一

How to update CK200 Auto Key Programmer?

How to update CK200 Auto Key Programmer?

CK200 Advantages:

1. Latest Software Vrsion: V39.09 (when newer software version release, email our customer sevice the serial number of CK200)
2. No Token Limitation
3. Updated version of CK-100 Key programmer, New generation Car Locksmith Tools

4. Add more car models in CK-200 Auto key programmer



CK200 Auto Key Programmer update frequently, the following are the tips to teach you how to update your CK200:

1. Enter to official site of CK200, register it online;
2.Dowload the latest software you need.

Attention: The serial number of the latest update software is the same with the device serial number.

BMW Carsoft 6.5 Software Installation Instruction

BMW Carsoft 6.5 Software Installation Instruction




Step 1: Copy the whole BMW Carsoft 6.5 File folder from the software driver CD to your hard-disk driver D or other hard driver. It is more stable and reliable to install the BMW Carsoft software from hard-disk directly.

Step 2: In the hard-disk driver where you pasted the whole BMW Carsoft 6.5 software, please open the File folder of BMW Carsoft 6.5, then double click “SETUP CAR SOFT.exe” to run the BMW Carsoft software.



Step 3: The BMW Carsoft software installation proceeds automatically, click “Next” button for software installation when you see the BMW Carsoft 6.5 Welcome surface.


Step 4: The BMW Carsoft software installation asking about Software License Agreement, click“Yes” button to proceed the BMW Carsoft software installation.


Step 5: The BMW Carsoft software installation asking about directory in your hard-disk, you can change the directory or keep the default directory “C:\Program Files\CARSOFT\BMW as it is,then click “Next” button to proceed the BMW Carsoft 6.5 software installation.


Step 6: The BMW Carsoft 6.5 program will be installed into your computer automatically.


Step 7: In the hard-disk driver where you pasted the whole BMW Carsoft 6.5 software, please open the File folder of BMW Carsoft 6.5, then open the file holder of “crack”, copy all 10 files in this holder,


Step 8: Then paste all those 10 new files into the file holder of “cm75f” at directory C:\cm75f\ (this directory was created during the BMW Carsoft 6.5 software installation automatically). The system will ask you if you want to replace old file during pasting those 10 new files into the file holder “cm75f”, click “Yes all” button to replace all old files by those cracked 10 new files in “cm75f” file holder.


Step 9: Then paste all those 10 new files into the file holder of “BMW” at directory C:\Program Flies\CARSOFT\BMW (this directory was created during the BMW Carsoft 6.5 software installation automatically). The system will ask you if you want to replace old file during pasting those 10 new files into the file holder “BMW”, click “Yes all” button to replace all old files by those cracked 10 new files in “BMW” file holder.


Step 10: Then you can run the BMW Carsoft 6.5 program now, click “Start” button at the left corner, select “Programs” menu, then select “CARSOFT” holder, click “BMW” to run the BMW Carsoft 6.5 program.


Step 11: Then you can see the BMW Carsoft Diagnostic program surface, click “BMW V6.5 WINDOWS” button to go ahead the BMW Carsoft 6.5 program.


Step 12: Then you can apply full functions of BMW Carsoft 6.5 Diagnostic program with the hardware together.